-
Why is 93% titanium dioxide more expensive than 97%
93% of the gaps in those 7 points are not impurities, but artificial coatings (SiO ₂, Al ₂ O ∝, ZrO ₂+organic treatment agents); 97% of them are mostly basic titanium dioxide particles with few coating/thin coating or even no coating, only with pure TiO ₂ and no post-treatment value. Pay attentio...Read more -
Which is more resistant to yellowing, rutile or anatase
Under the same coating conditions, the resistance to yellowing of rutile type is much better than that of anatase type. Sharp titanium type itself is basically not suitable for outdoor, long-term weather resistant systems, and is prone to yellowing and powdering. principle TiO ₂ is a photocatalyt...Read more -
Sulfuric acid method vs chlorination method for titanium dioxide
The sulfuric acid process is old, the raw materials are cheap, and it can produce rutile and rutile, but there is a lot of waste residue and acid; The chlorination method can only produce rutile with narrow particle size distribution, better whiteness and coverage, and less solid waste, but the r...Read more -
The influence of carbon black dispersion process on blackness and blue phase
The essence of dispersion is to break down carbon black aggregates and stabilize the separation of primary particles; Lack of dispersion → low blackness and brownish yellow color; Excessive dispersion (over grinding) → Blackness drop, weak blue phase transition, and even graying; The dispersion s...Read more -
Balancing environmental protection and practicality in varnish challenges
Environmental indicators (low VOC, no HAP, no free monomers, low odor, no heavy metals) often naturally clash with practical performance (water resistance, alcohol resistance, hardness, drying speed, construction window, storage stability, cost); Many clear paints that simply meet environmental s...Read more -
Why does the water resistance of high acid value resin decrease instead
The acid value represents a high content of carboxyl groups (- COOH) in the resin, which are strong hydrophilic groups; The higher the acid value, the more hydrophilic sites there are, and the easier it is to be soaked and absorb water after film formation, resulting in a decrease in water resist...Read more -
Phosphate ester vs. titanium ester adhesion promoter
Phosphate esters are mainly used for wet adhesion, salt spray resistance, and passivation of metal substrates; Titanate is a broad-spectrum coupling agent that balances filler dispersion and multiple substrates, with a low addition amount. However, it has weaker long-term wet adhesion to metals c...Read more -
Why does the water resistance of high acid value resin decrease instead
The acid value represents a higher number of carboxyl groups (- COOH) on the resin, which are essentially strong hydrophilic groups. At the same time, carboxyl groups bring more ionizable sites, making them easier to absorb water, hydrolyze, and be soaked by water. The macroscopic manifestation i...Read more -
What is the difference between solvent resin, water-soluble resin, secondary dispersion and lotion
Solvent based resin: resin molecules truly dissolve in organic solvents (homogeneous real solution) Water soluble resin (water diluted type): The resin chain carries hydrophilic groups, and after neutralization, it dissolves/colloids in a quasi homogeneous manner, not suspended particles · lotion...Read more -
Understand the directional arrangement of hydrogen evolution inhibition in water-based aluminum powder paint
Water based aluminum powder paint: mechanism and scheme of hydrogen evolution inhibition+complete directional arrangement of aluminum powder Core contradiction: Aluminum powder is a reactive metal, while water-based systems contain water pH、 Resin and additives jointly trigger the reaction betwe...Read more -
How to control the fullness of paint film
The essence of plumpness: After the paint film dries, it forms a full, warm, and three-dimensional feeling with thickness, not just a simple dry film thickness; The core is the volume retention rate from wet film to dry film, leveling, thixotropy, extinction/filler combination, and film continuit...Read more -
Why does adding leveling agents actually cause orange peel
Leveling agents regulate surface tension and cannot elongate the leveling window; Choosing the wrong, adding too much, not matching the system, and fighting with additives can create new surface tension gradients (Marangoni convection), forming wavy orange peel. 1. Excessive leveling agent Organi...Read more



